MINYAK RINGAN (Dua TAHAP) TEKAN 2G

Two Stage Light Oil Burners 

Pembakar seri PRESS 2G mencakup jarak tembak dari 107 hingga 1660 kW dan telah dirancang untuk digunakan dalam instalasi sipil dengan dimensi rata-rata, seperti area bangunan dan grup apartemen besar atau untuk digunakan dalam aplikasi industri, seperti pabrik kecil atau menengah. Operasi adalah dua tahap; pembakar dilengkapi dengan kotak kontrol keselamatan pembakar berbasis mikroprosesor yang memasok indikasi operasi dan diagnosis penyebab kesalahan. Kepala pembakaran, yang dapat diatur berdasarkan output yang dibutuhkan, memungkinkan kinerja optimal memastikan pembakaran yang baik dan mengurangi konsumsi bahan bakar. Fitur utama dari pembakar ini adalah keandalannya karena konstruksinya yang sederhana dan kuat, yang memungkinkan pengoperasian tanpa intervensi pemeliharaan khusus. Perawatan yang disederhanakan dicapai dengan sistem slide bar, yang memungkinkan akses mudah ke semua komponen penting dari kepala pembakaran. Semua komponen kelistrikan mudah diakses hanya dengan melepas panel pelindung, sehingga menjamin intervensi cepat dan sederhana pada komponen.

TECHNICAL DATA
Thermal power 415 / 830 -1660 kW – 356.900 / 713.800 – 1.427.600 kcal/h
Output 35 / 70 – 140 kg/h
Fuel Gas oil, max. viscosity at 20 °C: 6mm2/s (1.5 °E)
ELECTRICAL DATA
MOTOR IE1
Electrical supply Three-phase 220V +10% -10% ~ 60Hz without neutral
380V +10% -10% ~ 60Hz with neutral
Motor 10 A / 220V – 5.8 A / 380V
Ignition transformer Primary: 1.8 A / 220V – Secondary: 1x 8 kV – 30 mA
Absorbed electrical power 3.8 kW
MOTOR IE2
Electrical supply Three-phase 220V +10% -10% ~ 60Hz without neutral
380V +10% -10% ~ 60Hz with neutral
Motor 10 A / 230V – 5.8 A / 400V
Ignition transformer Primary: 1.8 A / 220V – Secondary: 1x 8 kV – 30 mA
Absorbed electrical power 4.1 kW

Specification STATE OF SUPPLY

Monoblock forced draught oil burner with two stage operation, fully automatic, made up of:
– Air suction circuit lined with sound-proofing material
– Fan with forward curve blades with high performance concerning pressure and air delivery
– Air damper for air setting
– Hydraulic ram for air damper control
– Starting motor at 2800 rpm, three-phase 400V with neutral, 50Hz (single-phase, 230V and 50Hz for the PRESS GW
model)
– Combustion head, that can be set on the basis of required output, fitted with:
– stainless steel end cone, resistant to corrosion and high temperatures
– ignition electrodes
– flame stability disk
– Fan pressure test point
– Gears pump for high pressure fuel supply, fitted with:
– filter
– pressure regulator
– connections for installing a pressure gauge and vacuometer
– internal by-pass for single pipe installation
– Valve unit with two delivery oil valves on the output circuit
– Photocell for flame detection
– Microprocessor-based burner safety control box, with diagnostic function
– Slide bars for easier installation and maintenance
– Protection filter against radio interference
– IP 44 electric protection level.
Standard equipment:
– 2 flexible pipes for connection to the oil supply network
– 2 gaskets for the flexible pipes
– 2 nipples for connection to the pump
– 4 screws for fixing the burner flange to the boiler
– 1 thermal screen
– Instruction handbook for installation, use and maintenance
– Spare parts catalogue.

LIGHT OIL (THREE STAGE) PRESS P 140 T/G

 Seri burner PRESS T/G mencakup jarak tembak dari 830 hingga 5340 kW. Tersedia dalam 4 model berbeda, pembakar ini sangat cocok untuk dicocokkan dengan boiler ruang bertekanan. Untuk karakteristiknya, mereka menemukan aplikasi di pabrik sipil besar untuk pemanasan rumah tangga atau aplikasi industri di mana beban termal berulang dan dapat diprediksi. Sistem eksklusif ram hidrolik, dengan 3 posisi yang dapat disesuaikan, mengatur bukaan damper, memungkinkan aliran udara sesuai dengan keluaran yang diperlukan: dengan cara ini stabilitas api dioptimalkan di setiap titik kerja, dengan pengaturan mikro tersedia. Pembakar dilengkapi dengan kotak kontrol keselamatan pembakar berbasis mikroprosesor yang memasok indikasi operasi dan diagnosis penyebab kesalahan.

Specification STATE OF SUPPLY

Monoblock forced draught oil burner with three stage operation, fully automatic, made up of:
– Air suction circuit lined with sound-proofing material
– Fan with forward curved blades high performance pressure levels
– Air dampers for air setting controlled by a three stage hydraulic ram
– Starting motor at 2850 rpm, three-phase 400 V with neutral, 50 Hz
– Combustion head, that can be set on the basis of the combustion output, fitted with:
– stainless steel end cone, resistant to corrosion and high temperatures
– ignition electrodes
– flame stability disk
– Gears pump for high pressure fuel supply, fitted with:
– filter
– pressure regulator
– connections for installing a pressure gauge and vacuometer
– internal by-pass for single pipe installation
– Valve unit with a oil safety valve and three oil delivery valves on the output circuit;
– Photocell for flame detection
– Microprocessor based burner safety control box, with diagnostic function
– Burner on/off switch
– Flame inspection window
– Slide bars for easier installation and maintenance
– Protection filter against radio interference
– IP X0D (IP 40) electric protection level.
Standard equipment:
– 2 flexible pipes for connection to the oil supply network
– 2 nipples for the connection to the pump
– 4 wiring looms fittings for electrical connections
– 4 screws for fixing the burner flange to the boiler
– 2 slide bar extensions (for the extended model of P 300 T/G and P 450 T/G)
– Gasket for flange
– 1 Star Delta starter (On models where provided)
– Diffuser disk (P 450 T/G)
– Instruction handbook for installation, use and maintenance

GAS BURNERS (MODULATING) GAS 10 P/M

Seri GAS P/M mencakup jarak tembak dari 130 hingga 4885 kW. Operasi ditampilkan oleh operasi dua tahap progresif atau modulasi penuh, dengan sistem kontrol dan probe modulasi canggih. Burner GAS seri P/M sangat cocok untuk aplikasi yang membutuhkan fleksibilitas kontrol (proses, uap, penyerapan pendingin) di mana output variabel diperlukan. Karena struktur lembaran logamnya, mereka secara khusus cocok rusak atau cacat. Perawatan yang disederhanakan dicapai dengan batang geser yang memungkinkan akses ke kepala pembakaran tanpa perlu melepas pembakar dari ketel

Specification STATE OF SUPPLY

Monoblock forced draught gas burner, two stage progressive operation or modulating with a kit, made up of:
– Air suction circuit
– Fan with forward curved blades
– Air damper for air setting controlled by a servomotor;
– Combustion head, that can be set on the basis of required output, fitted with:
– stainless steel end cone, resistant to corrosion and high temperatures
– ignition electrodes
– flame stability disk
– Servomotor for air and gas delivery regulation
– Maximum gas pressure switch (except for GAS 3 P/M model and GAS 6 P/M code 3753681)
– Minimum air pressure switch
– Single phase or three phases electrical motor
– Ionisation probe
– Flame inspection window
– Slide bars for easier installation and maintenance
– Protection filter against radio interference
– IP X0D (IP 40) protection level.
Standard equipment:
– 1 gas train flange
– 1 flange gasket
– 1 insulating screen
– 8 screws for fixing the burner flange to the boiler (12 for GAS 8 P/M – GAS 9 P/M and GAS 10 P/M)
– 4 wiring looms for electrical connections
– 1 star delta starter (for GAS 8 P/M – GAS 9 P/M and GAS 10 P/M)
– 2 wiring looms for electrical connections to the star delta starter (for GAS 8 P/M – GAS 9 P/M and GAS 10 P/M)
– 8 washers (for GAS 8 P/M – GAS 9 P/M and GAS 10 P/M)
– 2 bar extensions (only for extended head versions of GAS 8 P/M – GAS 9 P/M and GAS 10 P/M)
– Instruction handbook for installation, use and maintenance
– Spare parts catalogue.

MINYAK RINGAN (Dua TAHAP) RL 70

Pembakar seri RL mencakup jarak tembak dari 154 hingga 2700 kW, dan telah dirancang untuk digunakan pada ketel air panas bersuhu rendah atau sedang, ketel uap atau udara panas, ketel minyak diatermik. Operasi adalah “dua tahap”; pembakar dilengkapi dengan panel kontrol berbasis mikroprosesor, yang memasok indikasi status pembakar dan penyebab kesalahan. Optimalisasi emisi suara dijamin dengan desain khusus dari sirkuit pengisapan udara dan dengan bahan kedap suara yang terintegrasi. Performa kipas dan kepala pembakaran yang ditingkatkan, menjamin fleksibilitas penggunaan dan kerja yang sangat baik di semua tingkat pembakaran. Desain eksklusif memastikan dimensi yang lebih kecil, penggunaan dan perawatan yang mudah. Beragam aksesori menjamin fleksibilitas kerja yang tinggi.

Specification STATE OF SUPPLY

RL 50 – 64 MZ – 70 – 100 – 130 – 190 – 250 MZ models
Monoblock forced draught oil burner with two stage operation, fully automatic, made up of:
– Air suction circuit lined with sound-proofing material
– Fan with reverse curve blades (RL 50 – 70 – 100 – 130 models) or straight blades (RL 64 MZ – 190 – 250 MZ models)
– Air damper for air setting controlled by an adjustable hydraulic ram (or by a servomotor for the RL 250 MZ)
– Starting motor at 2800 rpm, three-phase 400V with neutral, 50Hz
– Combustion head, that can be set on the basis of required output, fitted with:
– stainless steel end cone, resistant to corrosion and high temperatures
– ignition electrodes
– flame stability disk
– Gears pump for high pressure fuel supply, fitted with:
– filter
– pressure regulator
– connections for installing a pressure gauge and vacuometer
– internal by-pass for single pipe installation
– Valve unit with an oil safety valve and two delivery oil valves on the output circuit
– Photocell for flame detection
– Microprocessor-based burner safety control box, with diagnostic function
– Burner on/off switch
– Flame inspection window
– 1st – 2nd stage manual switch
– Slide bars for easier installation and maintenance
– Protection filter against radio interference
– IP 44 electric protection level.
Standard equipment:
– 2 flexible pipes for connection to the oil supply network
– 2 gaskets for the flexible pipes
– 2 nipples for connection to the pump
– 4 screws for fixing the burner flange to the boiler
– 1 thermal screen
– Fairleads for electrical connections (RL 50 models)
– 2 slide bar extensions (for the extended head models and the RL 190 – 250 MZ models)
– Instruction handbook for installation, use and maintenance
– Spare parts catalogue.

RS SERIES Two Stage Progressive Gas Burners

PEMBAKAR GAS (Dua TAHAP

Seri pembakar RS/M mencakup jarak tembak dari 45 hingga 2650 kW, dan telah dirancang untuk digunakan pada ketel air panas bersuhu rendah atau sedang, ketel uap atau udara panas, ketel minyak diatermik. Pengoperasian dapat berupa “progresif dua tahap” atau, alternatifnya, “memodulasi” dengan pemasangan regulator logika PID dan masing-masing probe. Seri pembakar RS/M menjamin tingkat efisiensi tinggi di semua aplikasi, sehingga mengurangi konsumsi bahan bakar dan biaya operasional. Desain eksklusif memastikan dimensi yang lebih kecil, penggunaan dan perawatan yang mudah. Optimalisasi emisi suara dijamin dengan desain khusus dari sirkuit pengisapan udara dan dengan bahan kedap suara yang terintegrasi. Beragam aksesori menjamin fleksibilitas kerja yang tinggi.

Specification STATE OF SUPPLY

RS 34/M MZ – 44/M MZ models
Monoblock forced draught gas burner with two stage progressive or modulating operation, with a specific kit,
fully automatic, made up of:
– Air suction circuit with sound proofing material
– High performance fan with straight blades
– Air damper for air flow setting and butterfly valve for regulating fuel output controlled by a servomotor with
variable cam
– Starting motor at 2800 rpm, single-phase / 230V / 50-60Hz or three-phase / 230-400V / 50-60Hz
– Combustion head, that can be set on the basis of required output, fitted with:
– stainless steel end cone, resistant to corrosion and high temperatures
– ignition electrodes
– ionisation probe
– gas distributor
– flame stability disk
– Exclusive patented HCS (Housing Cooling System) with high thermal insulation and air circulation with continuous
air volume refresh for an active cooling system and avoid heat transfer to the electrical component housing
– Minimum air pressure switch stops the burner in case of insufficient air quantity at the combustion head
– Microprocessor-based burner safety control box, with diagnostic functions
– Plugs and Sockets for electrical connection, accessible from the external of the cover
– Burner on/off selection switch
– Manual or automatic output increase/decrease selection switch
– Flame inspection window
– Slide bars for easier installation and maintenance
– Protection filter against radio interference
– IP 40 electric protection level.
Standard equipment:
– 1 gas train flange
– 1 flange gasket
– 4 screws for fixing the flange
– 1 thermal screen
– 4 screws for fixing the burner flange to the boiler
– 3 plugs for electrical connection (RS 34-44/M MZ single-phase)
– 4 plugs for electrical connection (RS 44/M MZ three-phase)
– Instruction handbook for installation, use and maintenance
– Spare parts catalogue.

DUAL FUEL BURNERS (MODULATING) RLS 190/M MZ

 Seri pembakar RLS/M MZ mencakup jarak tembak dari 550 hingga 2460 kW, dan telah dirancang untuk digunakan dalam ketel air panas atau super panas, generator udara panas atau uap, ketel minyak diatermik. Operasi adalah “dua tahap” di sisi minyak dan “modulasi” di sisi gas dengan pemasangan regulator logika PID dan masing-masing probe. Pembakar seri RLS/M MZ menjamin tingkat efisiensi tinggi di semua aplikasi, sehingga mengurangi konsumsi bahan bakar dan biaya pengoperasian. Optimalisasi emisi suara dijamin dengan desain khusus sirkuit hisap udara dan penggunaan bahan kedap suara. Desain eksklusif memastikan dimensi yang lebih kecil, penggunaan dan perawatan yang mudah. Beragam aksesori menjamin fleksibilitas kerja yang tinggi.

Specification STATE OF SUPPLY

Monoblock forced draught dual fuel burner with two stage operation at the oil side and two stage progressive or
modulating operation at the gas side, with a specific kit, fully automatic, made up of:
– air suction circuit lined with sound-proofing material
– centrifugal fan with high performance and low sound emissions
– air damper for air flow setting and butterfly valve for regulating gas output controlled by a servomotor with variable
cam
– starting motor at 2800 rpm, three-phase 400V with neutral, 50Hz
– low emission combustion head, that can be set on the basis of required output, fitted with:
– stainless steel end cone, resistant to corrosion and high temperatures
– ignition electrodes
– gas distributor
– flame stability disk
– maximum gas pressure switch to stop the burner in the case of excess pressure on the fuel supply line
– minimum air pressure switch stops the burner in case of insufficient air quantity at the combustion head
– gears pump for high pressure fuel supply
– pump starting motor
– oil safety valves
– two oil valves (1st and 2nd stage)
– burner safety control box
– UV photocell for flame detection
– burner on/off selection switch
– manual or automatic output increase/decrease selection switch
– Oil/Gas selector
– flame inspection window
– slide bars for easier installation and maintenance
– protection filter against radio interference
– IP 44 electric protection level.
Standard equipment:
– 1 gas train flange
– 1 flange gasket
– 4 screws for fixing the flange
– 1 thermal screen
– 4 screws for fixing the burner flange to the boiler
– 2 flexible pipes for connection to the oil supply network
– 2 nipples for connection to the pump with gaskets
– Instruction handbook for installation, use and maintenance
– Spare parts catalogue.

GAS BURNERS (MODULATING) RS800/M BLU

RS 300÷1200/M BLU SERIES

 embakar BLU RS 300-400-500-650-800-1000-1200/M dicirikan oleh struktur monoblok yang berarti bahwa semua komponen yang diperlukan digabungkan dalam satu unit, membuat pemasangan menjadi lebih mudah dan lebih cepat. Pembakar mencakup jarak tembak dari 1350 hingga 11100 kW, dan telah dirancang untuk digunakan dalam ketel air panas atau generator uap industri. Pengoperasian dapat berupa “progresif dua tahap” atau sebagai alternatif “memodulasi” dengan pemasangan regulator logika PID atau dengan sinyal eksternal 4-20 mA/0-10 V. Perangkat regulasi cam mekanis memungkinkan untuk mengejar rasio modulasi tinggi pada semua rentang laju pembakaran. Oleh karena itu, pembakar dapat memasok daya yang diminta dengan presisi, menjamin tingkat efisiensi sistem yang tinggi dan pengaturan stabilitas, mendapatkan konsumsi bahan bakar dan pengurangan biaya pengoperasian. Kepala pembakaran, direkayasa dengan perangkat simulasi canggih, menjamin pengurangan emisi polusi (NOx < 80 mg/kWh). Versi FS1 dan FS2 tersedia untuk aplikasi operasi intermiten dan berkelanjutan. Desain eksklusif, menjamin emisi suara rendah, konsumsi listrik rendah, penggunaan dan perawatan mudah.

Specification STATE OF SUPPLY

Monoblock forced draught gas burner with modulating operation, fully automatic, made up of:
– High performance fan with low sound emissions, reverse curve blades for RS 300-400-1000-1200/M BLU, forward
curve blades for RS 500-650-800/M BLU
– Air suction circuit lined with sound-proofing material
– Air damper for air setting controlled by a high precision servomotor
– Air pressure switch
– Fan starting motor at 2900 rpm, three-phase 230/400 – 400/690 V with neutral, 50 Hz
– Low emission combustion head, that can be set on the basis of required output, fitted with:
– stainless steel end cone, resistant to corrosion and high temperatures
– ignition electrodes; or UV sensor (RS 1000-1200) for flame detection
– flame stability disk
– Maximum gas pressure switch, with pressure test point, for halting the burner in the case of over pressure on
the fuel supply line
– Burner safety control box for controlling the system safety (RMG/M for FS1 intermittent operation – LFL for FS1
intermittent operation for RS 1000-1200 model – LGK16 for FS2 continuous operation)
– UV photocell or ionisation probe for flame detection
– Star/delta starter for the fan motor (burners with motor electrical power ≥ 7,5 kW)
– Main electrical supply terminal board
– Burner on/off switch
– Auxiliary voltage led signal
– Manual or automatic output increase/decrease switch
– Burner working led signal
– Contacts motor and thermal relay with release button
– Motor internal thermal protection
– Motor failure led signal
– Burner failure led signal and lighted release button
– Led signal for correct rotation direction of fan motor
– Emergency button
– Coded connection plugs-sockets
– Burner opening hinge
– Lifting rings
– IP 54 electric protection level
Standard equipment:
– 1 flange gasket
– 8 screws for fixing the flange
– 1 thermal screen
– 4 screws for fixing the burner flange to the boiler
– Instruction handbook for installation, use and maintenance
– Spare parts catalogue.

Hubungi Kami

PT. INDIRA MITRA BOILER

☎️✔081388666204🔥